Monday, September 2, 2013

Networking a Home from the 1950s

The year is 1957. The world is being taken storm by a wave of new technology. The first artificial satellite Sputnik 1 was launched and Elvis Presley's Jailhouse Rock was holding the number one spot on music charts around the world. All of this happened, of course, long before I was born.

Along with these exciting historical events, a small home was built in Stoney Creek, Ontario. My parents have recently purchased this home with the intention to renovate it into the 21st century.

The front of the tired old home (before new windows).
Date of Manufacture
I was tasked with networking the home and I decided to take some pictures along the way. I have retrofitted Cat6 and RG6 into each bedroom and living space to pave the way for Home Theater PCs (HTPCs) and "Smart TVs". We use Channel Master 4221 antennas to receive local terrestrial ATSC signals. The RG6 will distribute this signal into each room. I purchased most of the supplies from the local Nutech Electronics and Home Depot.

The Cat6 and RG6 lines departing from the electrical panel. Looks good :]
Read on to see more details!

Thankfully this home has an unfinished basement. We are finishing it with a drop ceiling which allows me to staple cables onto the bottom surface of the floor joists. I started out with a good stapler and round "cable staples". The regular rectangular staples have a bad tendency of crushing cables.

A good stapler and staples are key.
The first RG6 line is intended for the chimney on the other side of the home where the antennas will be mounted. The second is for the TV in the front living room. I have decided to put two network drops in the living rooms.

The first run of Cat6 and RG6.
All of the RG6 drops are destined for the electrical panel. The network gear will be located in my bedroom next to the server, so all of the network drops terminate at the basement bedroom. I was careful to try to keep the RG6 and Cat6 somewhat separated from the mains AC where possible. In some cases it was simply unavoidable. I am using UTP Cat6 for this job.

Just the first two Cat6 runs and RG6 connections.
I have installed a 1-to-6 splitter to split the antenna signal into each room.

The antenna splitter next to the electrical panel.
Once I had all of the RG6 lines routed to the electrical panel, I mounted the splitter and installed the power supply for the Channel Master 7777 antenna preamplifier. I was lucky to salvage this CM7777 that had been dropped. There was a small crack on the Power Supply CCA that I was able to repair easily and test.

Completed Antenna Distribution
I left 25ft. of RG6 cable on the outside of the home to reach the top of the chimney for the future antennas to be mounted. It will be coiled up on the side of the home until after we move in.

Coiled RG6
Once I had all of the Cat6 drops routed into the basement bedroom it was time to install the keystone jacks and mount them on wall plates. An electrician recommended that I use these fantastic mounting plates. They do not require a stud or a junction box to secure the wall plate to. They simply grip the inside of the dry wall. They are called a "Low Voltage Mounting Bracket" and come in various shapes and sizes. I used the CARLON 1 Gang Low Voltage Mounting Bracket from Home Depot.

View from the back of the wall.
They mount very easily, you simply make a hole in the drywall and tighten the screws to increase their grip on the drywall.

View from the front, inside the bedroom.
After I pulled the cable, there were RG6 and Cat6 drops hanging from the basement ceiling ready to be routed into the walls in the rooms above.

One Cat6 and RG6 drop for each adjacent bedroom.
We all have our own cell phones so wiring plain old telephone system (POTS) into each room seemed like a waste. I have simply ran telephone into the basement bedroom where the modem will reside next to the network gear.

The right most keystone is for telephone. It is a little sloppy, but the rest are better.
The front of the partially completed face plate.

The rear of one of the completed face plates in the bedroom on the main floor.
Routing the cables from the basement onto the main floor wasn't terribly difficult. This home had 14/2 wiring which was replaced with proper 14/3 as part of the renovation so there were already holes in the floors that I could use.

[Correction, thanks Kent Sorensen]

This home was not wired with a ground to each outlet. The wiring was updated to modern Romex cabling that includes a grounded conductor. I was able to use the existing holes to help route the cables onto the main floor.

Cat6 and RG6 for the master and spare bedrooms.
The results of the job were great. Everything looks excellent and passed a basic cable test. Time will tell how well everything works once we move in at the end of the month.

Neat and tidy wiring. :]
This has been a long weekend and I am exhausted. I hope that these pictures and experiences will be valuable to someone in a similar position. Thank for reading!


  1. Nice. I wouldn't have bothered running the data cables in such nice ordered runs on top of the joists. Just drill a hole and run them through, Now they will interfere once you decide to finish the basement.

    I think you made a mistake when you said it was finished with 14/2. 14 is just the gauge, and 2 is the number of current carrying conductors. The ground wire is not counted. You mean it was done with cables without ground. 14/3 is something specific, namely a cable with two hot wires, and a neutral, plus ground.

    In the basement, you need to use at least 2x6 on the exterior walls. Minimum code for insulation of older houses is R20 IIRC. A bat of 6" Roxul will give you R24. Go with 24" on center. Less cold bridges.

    I just went through the same thing. just much more of it..

    1. Thanks Kent, I have included your correction.

      Your comments are appreciated!!

  2. Cables through wall studs or floor beams should be fitted inside a conduit. It would make it much easier to do modifications in the future.

  3. Those are some beautiful cable runs. Puts my work to shame. Although technically you shouldn't be stapling the cables like that since it pinches them. The proper way is to use the T59 with insulated staples

    1. Thanks!

      You are correct about the pinching, but I was careful to pull back the stapler slightly to avoid it. It probably took a lot longer than it would have if I had the perfect stapler.

  4. Very clean installation. I particularly like the orderly runs on the basement joists.

    Thanks for the post. I'll likely borrow a few of these techniques for a upcoming project I have.

  5. Thanks for taking the time to discuss that, I feel strongly about this and so really like getting to know more on this kind of field. Do you mind updating your blog post with additional insight? It should be really useful for all of us. best type of spray paint for metal

  6. I found so many interesting stuff in your blog especially its discussion. From the tons of comments on your articles, I guess I am not the only one having all the enjoyment here! keep up the good work... House Cleaning

  7. Thanks so much for this information. I have to let you know I concur on several of the points you make here and others may require some further review, but I can see your viewpoint. best toilets consumer reports

  8. Thanks so much for this information. I have to let you know I concur on several of the points you make here and others may require some further review, but I can see your viewpoint. electric shower head

  9. This is my first time visit to your blog and I am very interested in the articles that you serve. Provide enough knowledge for me. Thank you for sharing useful and don't forget, keep sharing useful info: Oklahoma Cannabis

  10. Very efficiently written information. It will be beneficial to anybody who utilizes it, including me. Keep up the good work. For sure i will check out more posts. This site seems to get a good amount of visitors. self publishing

  11. I am very happy to discover your post as it will become on top in my collection of favorite blogs to visit. professional painters New lenox

  12. I would like to say that this blog really convinced me to do it! Thanks, very good post. Scentsy

  13. Buy heroin online Great article Lot's of information to Read...Great Man Keep Posting and update to People..Thanks

  14. Home improvement loans can suck the life out your house hunting experience. Find out why home improvement loans suck and what you can do to stop the suck. premium glass pool fencing

  15. Thanks For sharing this Superb article.I use this Article to show my assignment in is useful For me Great Work. Best selling muzzleloaders

  16. I appreciate this blog your blog is vert help full for me i really enjoyed this stuff dude. 123movies

  17. There are four Essential Japanese Gardening Tools needed to create a serene space. Every gardener who understands that lifelong quality tools are better than cheaper tools that will need to be replaced every couple of years will appreciate using the quality and affordability of Japanese tools. best soil test kits

  18. Great write-up, I am a big believer in commenting on blogs to inform the blog writers know that they’ve added something worthwhile to the world wide web!.. Liv at MB

  19. Very efficiently written information. It will be beneficial to anybody who utilizes it, including me. Keep up the good work. For sure i will check out more posts. This site seems to get a good amount of visitors. Landscape Gardeners In Scotland

  20. Wow, cool post. I’d like to write like this too – taking time and real hard work to make a great article… but I put things off too much and never seem to get started. Thanks though. roofer in Dallas TX

  21. Home improvements are necessary if your current house is old. Getting a home improvement loan to 'upgrade' your house adds value to the property and makes living in it as comfortable as it can be. Even if the house is quite new, there may be the need to undertake that improvement to add something extra to it. In this article, we look at how to get approved for home improvement loans with the least fuss as possible. DIY lock install

  22. This is my first visit to your web journal! We are a group of volunteers and new activities in the same specialty. Website gave us helpful data to work. el gouna villa rentals

  23. Upgrading and renovating your home costs money, and depending on the type of home improvement project, it can cost a lot of money. However, what if that money isn't there right now and a new roof just doesn't fit into your budget? That's where home improvement financing and loans come into play. boundary fence company Sydney

  24. If you are like many homeowners, your house is among the most significant investments that you own. In addition to being your largest asset, it is the place where you live, entertain and more. By keeping your home well-maintained and making improvements as needed, you can easily maintain or improve its value while also enjoying increased pride of ownership. However, many home improvement projects can be costly, and you may be looking for a way to make home improvements more affordable. By following a few key tips, you can enjoy the benefits associated with improving your home without paying more than necessary for those improvements. roofing contractors